It is never pleasurable to notice new sounds on your vehicle. We always might worry and think about the worst. But experiencing wheel noise on Volkswagen Crafter is very often linked to small trouble that you can easily eliminate. To assist you in this examination, our team decided to produce this article to make your life easier and support you in this task. To do this, we will alternately see what are the distinctive noises that Volkswagen Crafter wheels can provoke and to which failures they are linked.
The different wheel noises on Volkswagen Crafter and their sources
We will therefore look into the different types of noise you may experience and their causes.
I listen to grinding wheel noise on Volkswagen Crafter from, cardan shaft
The first possibility of grinding wheel noise on your Volkswagen Crafter is that you feel a gimbal noise when you are turning significantly, usually at low speed. It is also conceivable that you may experience this noise when you pass over speed bumps. You should notice a noise close to a cracking . It is quite conceivable in this circumstance that one or more bellows of your gimbals are dead. In this case, the joint must be damaged and the transmission may fail. Check the state of the joint bellows and change them if necessary or risk having your vehicle immobilized. If they have cracks, they will rather quickly dry out and fill with dust or stones that will fairly quickly damage the cardan shaft itself, don’t wait to act! In case you have a noise when you pass on damaged roads but the gimbals are not responsible, read this article about suspension noise on Volkswagen Crafter to support you find a solution.
I find out a wheel noise Volkswagen Crafter when coasting attributable to a bearing
One of the other possible causes of symptoms on the front wheel of your Volkswagen Crafter when coasting, may be that one of your bearing is good to be changed, it will tend to generate a thumping noise that intensifies when it is stressed (turns faster and faster). So remember to examine by taking speed (neutral and window open to hear only the noise of the wheels) that the noise is well coming from here, if this is the case change it or them very quickly. If, on the other hand, this noise only manifests itself with an engaged speed, read this article about loud noises on Volkswagen Crafter, you will most likely find a resolution to your issue.
I listen to a wheel noise Volkswagen Crafter attributable to brakes
If you experience noise from one or both of your wheels, it is highly conceivable that it is your pads or discs that are the trigger. In fact, a disc or a set of dead plates will generate a loud metallic noise that you will undoubtedly notice. To examine this, put your vehicle on axle stands, and check the state of your discs and pads by getting rid of the wheel. If they are involved, change them in short order , otherwise you will no longer be able to brake. If you experience a metallic noise from your Volkswagen Crafter, but the brakes are not the cause, browse this article for more information on this issue.
I acknowledge a wheel noise Volkswagen Crafter connected to faulty wheel alingment
If you experience a noise that may be like a vibration and will increase as you increase speed, it is conceivable that your wheel alingment or balancing is the origin of it. Wheel alingment of a vehicle is a fundamental step that is generally done after each tire swap. It will ensure that the wheel rotates in a perfect axis and therefore that tyre wear is homogeneous and grip, ground contact is ideal. If your balancing weights are missing or incorrectly positioned, your wheels will tend to vibrate a lot and provoke a significant wheel noise on Volkswagen Crafter. Check that your seals are still set up, otherwise go to your garage.
I notice a wheel noise Volkswagen Crafter due to wishbone
Finally, you may experience a noise on your Volkswagen Crafter at the wheels, when you accelerate, you brake or in a rather random moment. It is likely that the trigger of this issue comes from the double wishbone suspension or the direction hinges. In fact, you will be able to test a damaged double suspension wishbone when you accelerate when it will be pushed on side and the vehicle will pull on the outside of the damaged wishbone (right wishbone pulls right) and when braking towards the inside of the same side (left wishbone pulls left). You can also examine the condition of the swivel bellows visually, which may affect the action of changing direction. If you are in one of these cases go to your mechanic.
