If you too have already experienced a grinding noise on Hyundai Bayon, you must have asked yourself the same questions as all Hyundai Bayon owners. We are rarely reassured when a grinding noise comes out on our car. As we are conscious of your fears and questions, we have chosen to compose this content to be able to support you in and ease your investigation for a solution to your problem. To do this, first we will see what the sources of a grinding noise on Hyundai Bayon are when you turn the wheel, then those of a grinding noise when you brake, if you have a grinding noise on Hyundai Bayon that originates from the shock absorbers and to finish from one of your doors.grinding-noise-hyundai-bayon

I acknowledge a grinding noise on Hyundai Bayon when I turn the wheel

First, we will look into the grinding noises on Hyundai Bayon that occur every time you turn the wheel of your car. Here are the main causes for this:

  • Hydraulic system
  • If you are subject to grinding noises on your Hyundai Bayon when you turn the wheels, it may be connected to the hydraulic system of your car that allows you to run the entire power steering part. In cases like this, the main point to verify is the power steering fluid level, which if below the normal level could be a sign of a leak of the unit. In this case, take into account to redo the level and verify it frequently. If the problem persists, go to your mechanic.

  • Bearings
  • “A grinding noise on Hyundai Bayon when I turn the wheels of my car” can also originate from premature wear of your bearings. In fact, bearings play an essential role in the good behaviour of the car when driving. When you turn at low speed and bring the steering to a stop, the pressure on the bearings is higher than at high speed, it can produce sounds close to a grinding if they are worn. Take into account to verify their condition.

  • Steering pump
  • Finally, a grinding noise on Hyundai Bayon when I turn may be related to a tired steering pump power steering pump. The goal of this organ is to run the steering belt, which will allow you to take advantage of the power steering. If the pump is tired, its operation will be impaired and squeaks may show up between it and the belt. Remember to verify that it is working properly.

    If despite these different solutions you continue to notice a grinding noise on Hyundai Bayon when turning your steering wheel, we have produced a complete content page on this subject that can support you discover the origin.

    I listen a grinding noise on Hyundai Bayon when braking

    If you acknowledge a grinding noise from the brakes of your Hyundai Bayon, it is highly imaginable that it will be linked with brake pads at the end of their life, indeed, the role of the pads is to act as a buffer during braking and they will therefore naturally wear out over time. Each manufacturer gives an average range in kilometres for pads, but based on your driving style and route, this may vary. Remove the wheels in question and verify the wear indicator on them. If they are dead they will have to be swapped promptly because they will promptly damage your discs.
    If, despite verification, your grinding noise on Hyundai Bayon does come from your brakes but is not connected to the pads, verify this content to find out the other conceivable origins of brake noises on Hyundai Bayon.

    I acknowledge a grinding noise on Hyundai Bayon at the shock absorbers

    If you are in the situation where you detect the grinding noise on Hyundai Bayon as coming from the damping part of your car, whether you are driving over a retarder, on a bumpy road, or simply when you change direction and the vehicle’s mass is swung from one side to the other. In this case, there are several causes that can explain this noise. In fact, you will have to verify some points, here they are:

    • You have an oil leak at a shock absorber, it is up to you to verify that there is no oil leaking from your shock absorbers.
    • You may encounter abnormal wear and tear on one of the seals. This would trigger an oil leak
    • Finally you can have one of your shock absorber cylinders deformed, which will generate a grinding noise on Hyundai Bayon

    at each compression.
    Once you have examined all these elements, you should have found the origin of your trouble, go to your mechanic to repair the faulty part. If you have not identified the origin of your problem, we would suggest that you look at this content which discusses all possible origins of shock absorber noise on Hyundai Bayon.

    I acknowledge a grinding noise on Hyundai Bayon at a door

    If that’s not enough, don’t hesitate to read this full content on door sounds on Hyundai Bayon.
    It is conceivable, determined by the type of noise you know, that the hinge of your door is at the origin of these noises. If this is the case, you will have to examine it by opening your door and checking that the grinding noise on your Hyundai Bayon comes from a hinge that is too dry. To solve this problem, first try to grease the hinge, in most cases this is enough to solve your problem. If that’s not enough, don’t hesitate to have a look at this complete content on door sounds on Hyundai Bayon.