Do you listen to an engine noise on your GMC Canyon when you drive your automobile? We know that this is very worrying and that you are questioning. Discovering such a noise is not always a good signal, but it may also be nothing severe. To support you eliminate this problem, our team has made a decision to compose this content page to assist you in this investigation. In order to conduct this research as accurately as possible, we will first focus on clicking noises, then on whistling noises and, finally, on engine noises on GMC Canyon metal type.engine-noise-gmc-canyon

I listen to a clicking engine noise GMC Canyon

In case you recognise a clicking engine noise on your GMC Canyon, and that this noise is close to a click, you will have to identify the source area of it to be able to know the reason of it. You will need a mechanical stethoscope or a large screwdriver to locate the original area of these noises.

I listen to a clicking noise coming from my high engine

If you listen to an engine noise on GMC Canyon, and this noise is located at the top of the engine, it means that it is located at your cylinder head and accompanying components. Two components can be the causes of these engine noises on GMC Canyon. Either the hydraulic pushers, generally it is because of their faulty “hydraulic catch-up” system that we will listen to these clicking noises, often when cold and vanishes when hot. Otherwise, it is your the play of your rocker arms or their state of wear that is the concern. In cases like this, reflect on swapping them.

I listen to a noise coming from the bottom engine of my GMC Canyon

If you have revealed the place of source of engine noise on GMC Canyon that comes from your low engine, it may be that your rods or piston shafts are the triggers. In both circumstances, the long-term risk is engine failure. These two repairs are very difficult and most technicians will advise you to swap the motor of your GMC Canyon.

I listen to an engine clicking noise on GMC Canyon coming from combustion

Finally, if you have the feeling that this clicking noise is connected to the combustion of your engine, there are three plausible triggers of it. Check the condition of your glow plugs which if worn can hinder the proper combustion of the fuel mixture. Then, your timing belt may be shifted and may poorly control the timing of the various engine elements to induce good combustion. And finally, the most classic reason, comes from your injection, which is either blocked or one or more injectors is affected. In this case, do not hesitate to refer to this content page which deals in detail with the different injector noises on GMC Canyon.

Hissing noise / engine friction GMC Canyon

Engine noise GMC Canyon close to a bearing

If it is close to a squeaking noise you may have one of the bearings of your engine accessory parts that are reached. So examine the condition and try to find the exact origins of this noise by positioning someone at the engine at idle, and if this noise is more likely to occur in high rpm, accelerate and position someone at the engine block to identify the location of origin of the noise. The three components whose bearings are often at the origin of these noises are the water pump, the injection pump and the oil pump.

Engine noise GMC Canyon when releasing or depressing the clutch

In the event that you perceive engine noise on GMC Canyon, but this noise happens mainly when you release or depress your clutch pedal, in such a case it is very likely that your release bearing is worn. Indeed, a worn release bearing will make a noise close to a bell noise. To have more information about this noise and if you have managed to validate that the release bearing is indeed the reason of your problems, go here, to find a complete file on release bearing sounds on GMC Canyon.

Engine noise GMC Canyon close to a friction

In the case that you listen to a motor noise on your GMC Canyon, and, that this noise is close to a friction, it is likely that one of your belts or one of the elements that triggers it is the source of your issues.Often, we will start to listen to a motor noise on GMC Canyon, close to a friction when one of the belts is worn out or when one of the related parts like your alternator, or your tensioner roller is the problem. So remember to examine their condition and go to your technician to change the components in question. If you have been able to target the noise as coming from the belts and you want more information about it, take a look at this content page on belt noise on GMC Canyon for a complete guide.

Metal motor noise GMC Canyon

In the case that you listen to an engine noise on GMC Canyon and this noise is similar to metal noise, it is plausible that this noise comes from your gearbox or clutch. Indeed, a metallic noise in the engine block is often connected with damaged sprockets. Try to examine that this noise comes from the transmission, if this is the case, almost instantly go to your motor mechanic or you would get a break down. Finally, the second possibility is that your silent engine blocks or rubber mounts may be dead. This triggers a metallic noise each time your engine moves, either because of a change of pace (acceleration or braking) or, when you pass on roads in poor condition. Check the condition of your silentblocks and change them if needed. If you want to have more information about rubber mounts noises on GMC Canyon, browse this content page which gives you more information about the different types of noise and their origins.